您的位置: 标准下载 » 国内标准 » 行业标准 »

HJ/T 399-2007 水质 化学需氧量的测定 快速消解分光光度法

时间:2024-05-20 11:35:45 来源: 标准资料网 作者:标准资料网 阅读:9348
下载地址: 点击此处下载
基本信息
标准名称:水质 化学需氧量的测定 快速消解分光光度法
英文名称:Water quality-Determination of the chemical oxygen demand-Fast digestion-Spectrophotometric method
中标分类: 环境保护 >> 环境保护采样、分析测试方法 >> 工业废水、污染物分析方法
ICS分类: 环保、保健与安全 >> >> 水质综合
发布部门:中华人民共和国环境保护部
发布日期:2007-12-07
实施日期:2008-03-01
首发日期:
作废日期:
主管部门:中华人民共和国环境保护部
提出单位:国家环境保护总局科技标准司
归口单位:国家环境保护总局科技标准司
起草单位:河北省环境监测中心站
出版社:中国环境科学出版社
出版日期:2008-03-01
页数:13页
适用范围

本标准适用于地表水、地下水、生活污水和工业废水中化学需氧量(COD)的测定。
本标准对未经稀释的水样,其COD 测定下限为15 mg/L,测定上限为1000mg/L,其氯离子浓度不应大于1000mg/L。
本标准对于化学需氧量(COD)大于1000mg/L 或氯离子含量大于1000mg/L 的水样,可经适当稀释后进行测定。

前言

没有内容

目录

没有内容

引用标准

GB/T 6682 分析实验室用水的规格和试验方法
GB/T 11896 水质 氯化物的测定 硝酸银滴定法
JJG 975 化学需氧量(COD)测定仪

所属分类: 环境保护 环境保护采样 分析测试方法 工业废水 污染物分析方法 环保 保健与安全 水质综合
【英文标准名称】:Steels--Micrographicdeterminationoftheapparentgrainsize
【原文标准名称】:钢.表观粒度的显微测定
【标准号】:JISG0551-2005
【标准状态】:作废
【国别】:日本
【发布日期】:2005-01-20
【实施或试行日期】:
【发布单位】:日本工业标准调查会(JP-JISC)
【起草单位】:TechnicalCommitteeonIronandSteel
【标准类型】:()
【标准水平】:()
【中文主题词】:
【英文主题词】:
【摘要】:この規格は,鋼のフエライト又はオーステナイトの結晶粒度を測定するための顕微鏡試験方法について規定する。また,この規格は,結晶粒界の現出方法及び一様に結晶粒が分布する試験片の平均結晶粒度の求め方について規定する。結晶粒の形状は,立体的(三次元)であるため,顕微鏡試料の切断面は,結晶粒の端部から最大直径の部分までの任意の箇所になり得る。たとえ結晶粒が完全に同じ大きさであっても,平面上(二次元)に現れる結晶粒の大きさは,ある範囲にばらつく。
【中国标准分类号】:H24
【国际标准分类号】:77_040_99;77_080_20
【页数】:59P;A4
【正文语种】:日语


Product Code:SAE J1453
Title:Fitting--O-Ring Face Seal
Issuing Committee:Hydraulic Tube Fittings Committee
Scope:This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and manufacturer to assure that required performance levels will be safe. See Figure 1.